Remember to use your hands!

Project Hannibal Old School

Project Hannibal Nerdy Sketch

My hands have been idle for a very very long time. Not good!
Although the project is entering into the next stage – 3D modelling, I’ll keep bombarding this place with hand drawn sketches.

More cool stuff on the way soon…

Jaguar XF S / R-Sport




Some press shots of the new Jaguar XF S & R-Sport model presented at the New York Auto Show earlier in 2015. Very pleased with the final result and fantastic team effort! Hopefully some design sketches will be released soon.

EIDO Concept: Episode IV – The Inside Matters!


It was about time to post some updates on the EIDO Concept. Since leaving the Design Studio of Aston Martin, I finally have some time to look back at my own design projects.

First of all, me and Peter had to put a stop on the exterior design development. We have some thinking to do before we go back and continue with the exterior. All this is due to the strange and unusual layout/specs of the car. The front mounted internal combustion engine working on liquid hydrogen and powering the front wheels plus electric motors aiding the rear wheels combined with the 3 seater layout, make it quite a challenge in terms of “engineering” (please excuse me for using this word so freely). There is no point of playing with the exterior of the car at the moment if the basic internal structure hasn’t been resolved. Since the goal of the project is to develop a highly-detailed design of a vehicle with the above mentioned challenges, I deem it to be a necessity to start developing the internal structure first.

To mention a few things we’ve been thinking on: The internal combustion engine working on liquid hydrogen will be front mounted. However I think the best solution so far is not to use anything larger than V6 cyl engine due to size restrictions. The challenge here though is to squeeze a decent space for a gearbox since the mid-passenger (the driver) is sitting quite forward in the centre of the car and his feet may end-up being inside the gearbox. This is something we have to work on and may cause additional joggle with the layout.
The electric motor powering the rear wheels is at the back of the car – similar construction to the Mercedes SLS AMG E-Cell. The single Electric motor placed in the middle of the car, between the rear wheels (in plan view) will power the rear axle thanks to ordinary drive shafts. That’s a much better solution instead the in-wheel-motors that leave no space for proper sports car suspension and wheel design too. The electric motor will be managed by power electronics sitting behind it. The positioning of the batteries is not a huge issue, as this is a short-range conceptual vehicle and big bulky batteries are not considered.
As for the carbon fibre chassis – this will be shaped according to all those functional elements and more. For the moment I am pulling and stretching the carbon fibre chassis in Alias, making sure there is enough of space for all the passengers and mechanical components in the car. It is a lot of work but it’s cool and exciting!!!!

To summarise: what you can see from this post is the initial design of the carbon-fibre chassis. It will give you an idea of the internal structure & assembly of the car. There are also sketches showing first designs on the interior as well..

More updates to follow before Christmas!

any comments anyone?


Feedback Welcome!

EIDO Concept: Episode III – initial 3D development


Back on it again!!!!! Recently me and Peter found couple of weekends to spend on this project and here are some screenshots and sketches of the initial Work-In-Progress on the EIDO Concept. We’re still pulling and stretching the wire in order to get the right proportions of the car, so everything is still considerably conceptual. Proper a-class surfacing will be done when the design freezes. There is sooo much work to be done on this project that it’s just incredible but spirit is up and we’re nearing 1% completion :) Thanks Peter!

Feedback Welcome!

Maserati GT-Uno, the sketch page

Maserati GT-Uno

In search for exterior themes…
This is 3000px wide Photoshop digital canvas, sketched with 5px fine brush only on my Wacom Intuos – all in one layer. It took me 4 days to complete, working every day 1.5-2hrs after work…accompanied by a glass of red one of course :)